Fire

Smoke Alarm Beeps 4 Times Then Stops

So, your smoke detector went off and then stopped? 

Did it beep three times? 

Or

You’re sure it went off four times and then stopped.

I am asking this because it happened to me as well.

I was sleeping, lost in my dreams, when suddenly

At around 3 am, a high-pitched annoying sound started coming into my ears and woke me up.

Yeah, that was the sound of my smoke detector going off.

I also couldn’t count how many times it beeped, but it was more than two times.

I hope you know what to do when the smoke alarm goes off in this alarming situation.

When a detector beeps once a day, two times, three times, and four times, all of these are signs that something is going on. It would help if you were wise enough to understand these signals.

Understand Beepings of A Detectors

There are different types of beeping signals that a smoke detector gives, and when nothing is wrong with the sensor, it will stay silent, but in case of beeps, you have to take action.

  • When the detector beeps two times, it has stopped working due to low battery; dust is stuck that you can clean with a vacuum cleaner or a blower. So, the detector will beep two times when there are faulty wirings, short circuits, or other reasons for the false alarms.
  • When the detector beeps every 3 to 4 minutes, that’s a low battery signal or the indication of a dead battery. The battery charge level is affected due to high temperature or insufficient supply. So, calling a professional is ideal for saving yourself from a significant hazard.
  • When the detector beeps three times after 3-4 minutes, the alarm malfunctions and requires troubleshooting.
  • If a break follows three beeps, the detector has detected the Smoke and is ringing the alarm due to Smoke. There can also be rising levels of carbon monoxide, which is a severe matter for homeowners.
  • If the alarm beeps five times every minute, that indicates an outdated or expired detector, and your warning needs replacement.

Smoke Alarm Beeps 4 Times then stops

Smoke Alarm Beeps 4 Times then stops

A smoke detector usually beeps when the battery is low or dead, which can be fixed by replacing the battery. Sometimes, a long troubleshooting list can be set off due to dust, dirt, insects stuck in it, steam, humidity, old error codes, and sudden temperature changes. But sometimes, there is real fire smoke that is causing the beeps, not the false alarm.

A smoke detector can behave differently when it detects fire and when there is a false alarm. So, above, we have already discussed what different noises mean and why the smoke alarm beeps continuously in the pattern so that you can figure out the reason for chirping and troubleshoot according to that.

You should also know about the types of smoke detectors because there are various types: battery-operated and hardwired.

What can cause the Smoke Alarm to Beep 4 Times

#1 – Battery Causing False Alarm

To silence the battery-powered detector, you must remove that detector from the ceiling by twisting it counterclockwise. No electrical wires and power supply are attached, so it will come off quickly. 

The best part is that sensors can detect low battery easily and keeps beeping until you replace them with a new battery. You won’t be able to ignore it as it will keep beeping once every minute, and the connected detectors won’t beep; only the one with the battery problem will beep.

Remove the batteries to interrupt the power, and the beep, flash, or siren will go off.

Another reason a detector can release high-pitched annoying beeps is when the battery is not inserted correctly and keeps beeping for an extended period. You may have to remove the battery by pulling the tabs because it won’t let the terminals connect properly, and power won’t reach the detector.

Still, it will warn you to insert new 9V rectangular batteries. You can remove the pull tab and close the door properly to ensure that the battery is fitted correctly; this way, you can prevent unnecessary chirping of the detector.

When replacing the batteries, keep in mind the polarity; there will also be signs of positive and negative terminals.

#2 – Detector is damaged or expired

The smoke detector is built to last up to 7 years, but I have seen that many people are using the same sensor for as long as ten years, which is not recommended for anyone with a family (It’s like putting the entire family at risk).

Thinking that the detector is working fine makes you vulnerable to hazardous Smoke because the sensor will wear out after a long time. Regardless of the battery levels, the CO detector may not be able to detect rising levels of CO.

Most of the time, the detector has worn out, expired, or broken, and in this condition, it can start beeping erratically, and those abnormal beeps are not because of the CO levels but due to the damaged sensor or parts of it. Therefore, you should consider replacing it once the time of life is passed for optimum protection.\

It would help if you never compromised on this and constantly checked the expiry date; otherwise, the detector would keep chirping.

Sometimes, it can also malfunction when the date is passed out, so it will be worth replacing it.

#3 – Error codes causing Detector to Beep

Moving on, the strange reason for the detector to trigger can be the log records of previous triggers because the sensor maintains logs which sometimes cause problems. Similarly, when you are changing the batteries, you should the detector will get off and blink three times before stopping, thanks to the previous instances, but to resolve this problem, press the sensor 5-10 times. It will contain the erratic Beeping for sure.

Error logs are only removed when you replace the battery. Otherwise, the internal processor won’t clear them unless you clean the codes yourself. Then, you can silence or mute the detector by pressing the reset button for a few seconds.

#4 – Smoke Detector Tripped and Caused Beeping

Most of the time, a situation occurs when the detector is tripped for any reason and goes into alarm with a pattern of three beeps.

#5 – Dirt Causing Beeping

As discussed earlier, a common reason for a carbon monoxide detector to go off is when the dirt is accumulated inside it that stops it from working correctly, so it starts beeping randomly.

You can dismount if they are battery-powered detectors or purchase an air blower from Amazon that will spray off the dust from the sensor.

There are also some uncommon reasons causing the smoke alarm to beep three times but no smoke.

You get more frustrated when you discover that you are being paranoid by the false alarm. False alarm can also be a significant stress factor because it creates unimaginable worry and unnecessary panic due to frequent beeps. Therefore, you should clean it frequently and ensure that it is not installed in areas with a lot of dust or humidity because these are the biggest triggers of the detector.

So, always keep a handy tool like a vacuum cleaner or an air blower to blow off or suck the dust or dirt from the detector because sometimes, the sensor can think of land as Smoke and start beeping crazy.

#6 – Steam Caused Beeping

If you have installed the smoke detector near the bathroom by mistake, chances are it will go off randomly due to the steam coming from the bathroom when you shower, which can cause a false alarm.

So, when taking a steamy shower in a bathroom, make sure to fan off the detector with a magazine.

#7 – Change in Temperature can cause Beeping

Sometimes, there can be sudden changes in the room temperature, like when you use the air conditioner, and suddenly the hot wind blows in, or if you have a compact home with poor ventilation, then the kitchen heat, appliance temperature, and thermostat temperature can cause the unnesssecary Beeping. Therefore, the CO detector should be installed wisely, away from regular CO emission plates.

So, if you are enjoying summer and the AC is working fine, but suddenly someone opens the door or window, and a strong gust of hot air comes inside, it can trigger the heat sensor to start beeping.

Similarly, if you are cooking in a closed apartment, the heat produced from the stove can trigger the detector.

So, either reposition the detector or cook while the door is closed so the smoke detector won’t catch extreme temperature changes.

#8 – Actual Fire Causing the Beeping

Another situation that can cause the detector to go off is the actual fire incident in the house. Therefore, the recommended option for homeowners is that they should integrate all the sensors and must be connected with the grid for constant provision of electricity. If by accident, there are rising levels of CO in one place, all the connected detectors will go off telling you that something is wrong, and you have to figure that out. Then, you can try to identify the source or, without wasting time, empty the premises and get every living body out of the home until the emergency responders do not arrive.

If you have configured the detectors with each other, if one detects Smoke, all sensors will start chirping to alert you as a homeowner to take the necessary steps to save you and yourself from the fire.

Well, you can start smelling it, doing a thorough inspection, and see if there is a fire in any room. Just exit the home with your family and pets and call the fire department.

 

#9 – Stop a Smoke Detector with no battery to stop chirping

The case for a hardwired smoke detector is different as the sensor is now connected to the home electric system and won’t shut down by simply removing the backup battery.

If the wiring is not underground, then unplug the detector switch from the outlet or remove the red wire clip from the detector by squeezing the tag to open the clip. There are more wires as well, but they are useless right now. Then, it’s also ideal for removing the backup batteries as well.

If it’s a hardwired detector, you can unplug the detector switch, pull down the breaker switch, or remove the red wire connected to the sensor by squeezing it.

Then, you have to deal with the backup battery because that will keep powering the detector, and for that, the only solution is to turn off the circuit breaker. Still, it will disable all the sensors in your home, making you unprotected.

Therefore, never compromise on this and instantly replace the battery without putting your family in danger.

#10 – Smoke Detector beeping three times

When the smoke detector beeps three times, you have to be cautious, especially when it beeps three times, pauses for a moment, and then beeps three times. 

That’s not a low battery signal, that’s a signal of actual fire inside your home, and if the detector beeps four times with a gap, that’s the sign of carbon monoxide in your home.

So, you should immediately call the emergency responders or the nearest hospital and leave the premises with your family and pets. Before that, you can try opening all the doors and windows so that the trapped air and Smoke can exit the house.

#11 – All Smoke detectors beeping at once

Another situation is when you have installed multiple interconnected smoke detectors in your home, and all of them go off when one goes off, making you super frustrated because all of them will start sounding simultaneous. 

A quick solution is disconnecting the power source of all the smoke detectors by removing the circuit breaker labeled as a smoke detector and then removing the batteries.

When all the interconnected detectors start beeping, the one is the culprit, which will most certainly behave differently than the rest.

So, you have to locate that one because it will have a steady red light and start with compressed air to remove the dust to see if the Beeping has ceased.

As you have seen earlier, there can be a lot of reasons for the Beeping, so you may not exit the room while it’s 3 am.

Related Articles

How to stop Smoke Detector Beeping without battery

Carbon Monoxide Detector Going off But No Gas Appliance

First Alert Carbon Monoxide Detector Beeping 5 Times

Latest posts by Robert Smith (see all)

About the author

Robert Smith

Robert Smith is a technology lover and loves to write about laptops, monitors, printers, tablets, Apple products and anything that's related to computers and games. He is passionate enough that he maintains this blog regarding tech updates on a daily basis.